<dfn id="8wqko"></dfn>
  • <ul id="8wqko"><sup id="8wqko"></sup></ul><fieldset id="8wqko"><menu id="8wqko"></menu></fieldset> <strike id="8wqko"><menu id="8wqko"></menu></strike>
  • <ul id="8wqko"></ul>
  • <strike id="8wqko"></strike><strike id="8wqko"></strike>
  • <fieldset id="8wqko"></fieldset>

    加載中...

    點擊這里給我發消息

    QQ群:417857029

    新產品·新技術信息

    硬包裝使用的水性膠粘劑

    來源:林中祥膠粘劑技術信息網2011年01月15日

    閱讀次數:


    Waterborne Adhesives for Rigid Packaging Uses



    While aqueous solutions, dispersions and emulsions have been the most commonly used adhesives in the packaging industry,1 there are many settings in which hot-melts and other products are preferred. Thats in part down to one major weakness in waterborne formulations - long setting times, caused by the need for water to evaporate.2 However, in recent years researchers have striven to overcome this, and have gone some way towards rectifying the deficiency.

    Waterborne adhesives are often used in packaging in conjunction with paper and board materials. Due to their relatively low viscosity, water-based adhesives can be sprayed or extruded in a thin layer that forms a strong adhesive bond. Their low viscosity also means that they can penetrate porous substrates, rapidly giving a high degree of tack and stronger bonding than is achievable with hot-melt adhesives.

    While hot-melt adhesives soften at temperatures over 75°C and may become brittle near 0°C waterborne adhesives remain bonded strongly over a greater temperature range. They can also make packaging, for example corrugated containers, that can be re-pulped and recycled without removing or separating the adhesive layers, another distinct advantage over hot-melts.

    Yet, in applications like sealing corrugated fibreboard containers made from pre-cut flats, setting time remains the most critical property. Under the type of compression typically used on carton sealing lines, a hot-melt adhesive will set in about 1 to 3 seconds, as compared with 10 to 20 seconds for a water-based adhesive.

    硬包裝使用的水性膠粘劑

    What is your opinion about the Future
    of Adhesives in Rigid Packaging?

    Participate to our 7 minutes survey and get the
    feedback of your peers by mid-February!

    硬包裝使用的水性膠粘劑

    硬包裝使用的水性膠粘劑
    Figure 1: Succinic anhydrides that can reduce the hydrophilicity of polymers emulsified in waterborne adhesives, increasing their setting speed.

    While its possible to try and overcome this difficulty through adapting the adhesive dispensing process, novel adhesive formulations can also tackle it. For example, many waterborne packaging adhesives are based on starch or poly(vinyl acetate) (PVA) and poly(ethylene-vinyl acetate) (EVA) resin emulsions. In these curing speed can be accelerated by incorporating a starch modified with succinic anhydride functionality.3 Octenyl succinic anhydride (OSA) and dodecenyl succinic anhydride (DDSA) are particularly effective in improving the drying speed of waterborne EVA and PVA adhesives.

    Dont hesitate to react about this Article

    硬包裝使用的水性膠粘劑 Anhydride waterborne adhesives dry quicker

    Anhydride molecules are attached to hydroxyl groups within the composition of the formulation. An appropriate cross-linker is then applied to tie up the hydrophilic groups and make them perform hydrophobically. This reaction serves to change the surface tension and cause the water molecules to disperse more rapidly, and therefore promote improved drying rates. For OSA groups the crosslinker would be aluminium sulfate, while in DDSA groups it would be calcium chloride.

    While starch contains hydroxyl groups that can be modified with these anhydrides, EVA and PVA do not. Instead, formulations based on these polymers tend to exploit hydroxyl-containing chemicals, for example as stabilizing and dispersing agents. These can also be starch molecules, as well as dextrins or polyvinyl alcohol (PVOH). Some of the fastest curing waterborne adhesives are based on EVA stabilized by PVOH and containing starch which contains between 2-5 percent by weight of OSA groups bound to it.

    These anhydride-modified corn starches are commercially available, and can simply be added to waterborne adhesives to modify them. For example, researchers have added an aluminium sulfate crosslinked corn starch carrier containing 3% OSA directly to EVA emulsions containing PVOH colloid groups and allowed it to mix for thirty minutes. They then assessed these different formulations setting speed on the wire side of unbleached Kraft base stock, and also gauged bond strength in a Kraft fibre tear test. Untreated EVA resins took eleven seconds to set, and scored 65 percent in the tear test. Adding five percent crosslinked starch to the formulation reduced setting time to five seconds, and increased the tear test performance to 100 percent, which is considered the ultimate bond strength.

    • 標簽:
    相關閱讀

    本站所有信息與內容,版權歸原作者所有。網站中部分新聞、文章來源于網絡或會員供稿,如讀者對作品版權有疑議,請及時與我們聯系,電話:025-85303363 QQ:2402955403。文章僅代表作者本人的觀點,與本網站立場無關。轉載本站的內容,請務必注明"來源:林中祥膠粘劑技術信息網(www.nongfusping.com)".

    網友評論

    ©2015 南京愛德福信息科技有限公司   蘇ICP備10201337 | 技術支持:南京聯眾網絡科技有限公司

    客服

    客服
    電話

    1

    電話:025-85303363

    手機:13675143372

    客服
    郵箱

    2402955403@qq.com

    若您需要幫助,您也可以留下聯系方式

    掃二
    維碼

    微信二維碼
    久久久精品人妻一区二区三区| 久久永久免费人妻精品| 日产精品久久久久久久| 国产精品视频2020| 久久99精品国产麻豆宅宅| 精品69久久久久久99| 亚洲国产精品无码久久青草 | 亚洲国产精品SSS在线观看AV| 国产精品久久久久久网站| 四虎国产精品永久免费网址| 无码日韩人妻av一区免费| 中文字幕日韩精品麻豆系列| 精品一区二区三区电影| 国产精品天天看大片特色视频| 国内少妇人妻偷人精品xxx| 国产成人精品999在线| 亚洲精品在线网站| 久夜色精品国产一区二区三区| 国内精品久久久久久影院| 精品无人区麻豆乱码无限制| 亚洲mv国产精品mv日本mv| 中文字幕一区二区三区日韩精品 | 精品三级AV无码一区| 国产2021久久精品| 日韩精品久久一区二区三区| 午夜福利麻豆国产精品| 久久精品亚洲综合| 国产精品多p对白交换绿帽| 日韩精品视频免费在线观看| 国产大片51精品免费观看| 精品国产三级a∨在线观看| 99久久免费精品国产72精品九九| 亚洲欧洲国产精品你懂的| 亚洲国产精品无码久久一线| 国产精品va无码一区二区 | 麻豆麻豆必出精品入口| 亚洲午夜国产精品| 国产精品高清视亚洲精品| 国产精品福利尤物youwu| 国产精品三级在线观看无码| 久久国产乱子伦精品免费强|